Track Machine Quiz - 27

Track Machine Quiz – 27 इस प्लेटफार्म पर आपको ट्रैक मशीन से संबंधित ऑब्जेक्टिव टाइप्स महत्वपूर्ण प्रश्न और उत्तर मिलेगे।

Track Machine Quiz – 27

QUIZ START

Results

Congratulations.

#1. If more than 50 mm lift is required, it should be undertaken by

Three passes of tamping machine.

One passes of tamping machine.

Two passes of tamping machine.

All

#2. While fixing the target level, for datum rail, care should be taken to make sure that total lift value does not exceed ………… at any point on Datum rail.

60 MM

50 MM

80 MM

90 MM

#3. Deciding General Lift

The lifting of the track is decided based on the magnitude of the peaks in the track.

The lifting of the track is decided based on the magnitude of the dips in the track.

The lifting of the track is decided based on the magnitude of the dips/peaks in the track.

All of above.

#4. Value of Ramp in Ramp out.

1 in 10

1 in 10000

1 in 100

1 in 1000

#5. Which brake, applied when machine is stabled.

Safety Brake.

Parking Brake.

Emergency Brake.

All of above.

#6. Which brake is applied automatically by switching off hydrodynamic transmission gear (ZF Gear in Plasser machines).

Indirect Brake.

Emergency Brake.

Safety Brake.

All of above.

#7. Speed of Working of DTS.

0.2 kmph to 0.8 kmph

1.0 kmph to 2.0 kmph

0.5 kmph to 1.0 kmph

All of above.

#8. Which lining method restores the geometry to almost perfect provided correct measurements are fed.

2- Point Lining method.

4- Point Lining method.

3- Point Lining method.

All of above.

#9. Which lining method used in tamping machine mainly curve track.

1- Point Lining method.

2- Point Lining method.

3- Point Lining method.

4- Point Lining method.

#10. Tamping machines follow ………. methods of alignment correction.

#11. On curved track should be taken as reference rail.

Outer rail.

Inner rail.

Both rail.

All of above.

#12. Tools with more than ………. wear of the original surface area should not be used.

10%

20%

30%

40%

#13. Squeezing time of …….. second to ……. second should normally be adequate.

0.8 second to 1.2 second.

0.1 second to 2.2 second.

2.8 second to 3.2 second.

3.8 second to 4.2 second.

#14. The vibration pressure varies from machine-to-machine and ranges from ………

150 to 210 Kg/cm2.

250 to 310 Kg/cm2.

350 to 410 Kg/cm2.

100 to 210 Kg/cm2.

#15. Tamping tools Amplitude of oscillation.

1-5 mm

2-5 mm

3-5 mm

4-5 mm

#16. Weightage factor for RGM (72 stones ) is ——-

4.5

1.0

1.5

2.0

#17. Schedule-VI for BCM is to be completed in ——–

45 days

90days

120 days.

None of above

#18. Which of the following is the mode of working with ALC

Measuring run

Geometric mode

Both a & b

Smoothening mode

#19. At how many hours Schedule-IV for 09-3X machine is to be attended.

200hrs.

500hrs.

1000hrs

2000 hrs

#20. At how many hours Schedule-III- for 09-3X machine is to be attended.

100hrs.

200hrs

500hrs.

1000 hrs

#21. The hydraulic oil used in Rail Grinding Machine is-

HLP-68

Water Glycol

Servo-317

None of above

#22. How many disc clamp rollers are used in BCM Machine–

2 Nos.

8 Nos.

4Nos.

#23. How many track lifting cylinders are used in a tamping machine.

One

Two

Three

Four

#24. How many lining cylinders are used in one lifting unit –

One

Two

Three

Four

#25. Inspection Schedule by Dy.CE/TM/Lines for TRT.

once in 6 months.

once in 3 months.

once in a year.

once in 2 months.

Finish

दोस्तो उम्मीद है आज आपको ये क्विज अच्छा लगा होगा। अगर आपके अभी भी कोई सवाल इंजीनियरिंग से जुड़े है, तो आप हमे कमेन्ट करके जरूर बताये।

टेक बासुदेव (Tech Basudeo) से जुड़ने के लिए आपका धन्यवाद। 🙂

अगर आप टेक्निकल की वीडि मे देखना पसन्द करते है, तो आप हमारे YouTube Channel Tech Basudeo को जरूर विजिट करे।

अन्य क्विज –

Track Machine Quiz

Track Machine Quiz – 01

Track Machine Quiz – 02

Track Machine Quiz – 03

Track-machine-quiz-04

Track Machine Quiz – 05

Track Machine Quiz – 06

Track Machine Quiz – 07

Track Machine Quiz – 08

Track Machine Quiz – 09

Track Machine Quiz – 10

Track Machine Quiz – 11

Track Machine Quiz – 12

Track Machine Quiz – 13

Track Machine Quiz – 14

Track Machine Quiz – 15

Track Machine Quiz – 17

Track Machine Quiz – 18

Track Machine Quiz – 19

Track Machine Quiz – 20

Track Machine Quiz – 21

Track Machine Quiz – 22

Track Machine Quiz – 23

Track Machine Quiz – 24

अन्य पढ़ें –

Resistance And Resistor

Electric Circuit

Ohm’s Law

Combination Set

Metal Cutting Method

Vernier Micrometer

Results

#1. If more than 50 mm lift is required, it should be undertaken by

#2. While fixing the target level, for datum rail, care should be taken to make sure that total lift value does not exceed ………… at any point on Datum rail.

#3. Deciding General Lift

#4. Value of Ramp in Ramp out.

#5. Which brake, applied when machine is stabled.

#6. Which brake is applied automatically by switching off hydrodynamic transmission gear (ZF Gear in Plasser machines).

#7. Speed of Working of DTS.

#8. Which lining method restores the geometry to almost perfect provided correct measurements are fed.

#9. Which lining method used in tamping machine mainly curve track.

#10. Tamping machines follow ………. methods of alignment correction.

#11. On curved track should be taken as reference rail.

#12. Tools with more than ………. wear of the original surface area should not be used.

#13. Squeezing time of …….. second to ……. second should normally be adequate.

#14. The vibration pressure varies from machine-to-machine and ranges from ………

#15. Tamping tools Amplitude of oscillation.

#16. Weightage factor for RGM (72 stones ) is ——-

#17. Schedule-VI for BCM is to be completed in ——–

#18. Which of the following is the mode of working with ALC

#19. At how many hours Schedule-IV for 09-3X machine is to be attended.

#20. At how many hours Schedule-III- for 09-3X machine is to be attended.

#21. The hydraulic oil used in Rail Grinding Machine is-

#22. How many disc clamp rollers are used in BCM Machine–

#23. How many track lifting cylinders are used in a tamping machine.

#24. How many lining cylinders are used in one lifting unit –

#25. Inspection Schedule by Dy.CE/TM/Lines for TRT.

Leave a Comment Cancel reply